View FRD4812_367930.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(888) IPD-CONVerters q (888) 473-2668
q
www.ipdconverters.com
FRD SERIES - DUAL OUTPUT, 5 WATT
DESCRIPTION FEATURES * 500V Isolation * Short Circuit Protection * 6-Sided Shielding FRD dual output DC/DC converters offer excellent * Wide Input Range regulation and isolation in an industry standard * Trim and Enable Pins package. Available in several input versions, the FRD * Remote Sense Pins is perfect for industrial, datacom, or telecom applications. The FRD features short circuit protection, six-sided shielding, and 500 VDC isolation. Please see the FRS series for single output applications.
80 75 70 65 60 55 50 45 40 35 10 20 30 40 50 60 70 80 90 10
Efficiency vs. Load (28V Input)
EFFICIENCY %
EFF. FRD2812 EFF. FRD2815)
TECHNICAL SPECIFICATIONS
Input Voltage Range Reflected Ripple Reverse Input Current 5V, 12V, 24V, 28V, and 48V Nominal See selection chart for specific input range. 20% Iin Max. 100% Iin Max.
LOAD %
Efficiency vs. Load (48V Input)
70 65 60 55 50 45 40 35 30 25 10 20 30 40 50 60 70 80 90 10
LOAD %
EFF. FRD4812 EFF. FRD4815
Output Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated 1% Vout 0.15% Vout
Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Short Circuit Protection1
0.15% Vout Iout Rated 10 % lout Rated Continuous
General Switching Frequency Isolation Input - Output Isolation Resistance - Input to Output Case Temperature Operating Range Storage Range Humidity Max, Non-Condensing Temperature Coefficient Vibration, 3 Axes, 5 Min Each Safety Weight (Approx.) 20 kHz 500 VDC 109 Ohms -25 To +85C -40 To +125C 95% 0.02%/C 5 g, 10 - 55 Hz Consult Factory 2.2 oz Notes
Specifications typically at 25C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information.
C-64
EFFICIENCY %
MTBF predictions may vary slightly from model to model.
FRD SERIES - DUAL OUTPUT, 5 WATT
MODELS - (See the last page of this file for options.)
Vin (Volts) 5 5 12 12 24 24 28 28 48 48 Vin Range (Volts) 4.65 - 5.50 4.65 - 5.50 10.90 - 13.20 10.90 - 13.20 21.60 - 26.40 21.60 - 26.40 25.20 - 30.80 25.20 - 30.80 43.20 - 52.80 43.20 - 52.80 Iin Max.* (Amps) 2.01 2.04 0.85 0.86 0.43 0.45 0.37 0.38 0.21 0.22 Vout (Volts) 12 15 12 15 12 15 12 15 12 15 Iout Rated (Amps) 0.23 0.19 0.23 0.19 0.23 0.19 0.23 0.19 0.23 0.19 Ripple & Noise Pk-Pk (mV) 40 40 40 40 40 40 40 40 40 40 Efficiency Typ. ** 65% 66% 66% 67% 66% 65% 69% 71% 65% 66% Model FRD512 FRD515 FRD1212 FRD1215 FRD2412 FRD2415 FRD2812 FRD2815 FRD4812 FRD4815
* Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output.
MECHANICAL DRAWING
2.00" (50.8mm) 0.18"(4.6mm) MIN. 0.100" -0.300" (-7.6mm) (2.5mm) 1.40" (35.6mm) 0.500" (12.7mm)
0.800" (20.3mm)
3
4
5 2.00" (50.8mm)
BOTTOM VIEW
1
0
2
DIA 0.040" (1.0mm)
0 0.200" (5.1mm)
0.40" 1.10" (27.9mm) (10.2mm)
Thermal Impedance Natural convection 100 LFM 200 LFM 300 LFM 400 LFM 10.3 7.7 6.3 5.1 4.1 C/W C/W C/W C/W C/W
Pin 1 2 3 4 5
Function +Vin -Vin + Vout Common - Vout Inches: .XX 0.040 .XXX 0.010 Pin: 0.002 Case: + 0.04, - 0.00
Tolerances (Millimeters) .X 1.0 .XX 0.25 0.05 + 1.0, - 0.0
Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application.
(Tolerances as listed unless otherwise specified.)
C-65
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table.
OPTION Negative Logic Lucent Compatible Trim Terminal Strip Trim Enable Trim and Enable Current Share Headerless SUFFIX N T TS 1 2 3 4 Y APPLICABLE SERIES HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD HAS, HBD, HBS, HES, QBS, QES XWS, XWD, XWT IAS, LES IAD, IAS, LES, SMS IAS, LES SMS Encapsulated EWS, IWS, OWS REMARKS TTL "Low" Turns Module ON TTL "High" Turns Module OFF
PIN LENGTH AND HEATSINK OPTIONS 0.110" (2.8mm) Pin Length 0.150" (3.8mm) Pin Length 0.24" (6.1mm) Horizontal Heatsink 0.24" (6.1mm) Vertical Heatsink 0.45" (11.4mm) Horizontal Heatsink 0.45" (11.4mm) Vertical Heatsink 0.95" (24.1mm) Horizontal Heatsink 0.95" (24.1mm) Vertical Heatsink 8 9 1H 1V 2H 2V 3H 3V All Units (Except SMS) All Units (Except SMS) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages)
Standard Pin Length is 0.180" (4.6mm)
Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95" vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110" pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
C105

▲Up To Search▲

Price & Availability of FRD4812

	To Download FRD4812 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .